A large share of Ackerman, MS homes built in the mid-1960s and early 1970s still run on original aluminum branch circuit wiring, a known contributor to household electrical fires. Wired Right Electrical identifies every risk point and corrects it with proven, code-compliant methods carried out by certified electricians.
☎ Call 1 (855) 471-2673When copper prices spiked in the mid-1960s, many builders switched to aluminum for branch circuit wiring, and a number of Ackerman, MS homes from that construction wave still carry that original wiring behind their walls. Aluminum itself isn't defective, but it reacts to electrical load in ways copper does not, and those differences can quietly build into a genuine fire hazard if the wiring is never addressed.
The trouble stems from how much aluminum expands and contracts compared to copper as current flows through it. Each heating and cooling cycle gradually loosens the connections at switches, outlets, junction boxes, and panel terminals. A loosened connection creates resistance, resistance generates heat, and unchecked heat near combustible framing materials is how house fires start. Federal safety data has repeatedly linked homes wired with aluminum branch circuits to a markedly higher rate of electrical fires compared to copper-wired homes.
Wired Right Electrical carries out full aluminum wiring correction projects for Ackerman, MS homeowners, relying on techniques recognized by federal safety regulators and accepted across the insurance and inspection industries. We start with a room-by-room inspection to map out every point where aluminum conductors meet a device, fixture, or panel terminal, then match each connection to the correction method it actually needs.
Our preferred long-term fix is copper pigtailing — sometimes called the AlumiConn or COPALUM approach — where a short length of copper wire is joined to the existing aluminum conductor using a connector specifically listed for aluminum-to-copper splices. The result is a copper connection at every device throughout your Ackerman, MS home, removing the aluminum-to-device contact points that cause problems. We finish every splice with a listed anti-oxidant compound, since oxidation on aluminum strands is its own separate source of resistance and heat.
In situations where CO/ALR-rated devices make more sense, our crews install switches and receptacles engineered for direct use with aluminum conductors. Their terminal design is built to hold a solid connection despite aluminum's expansion and contraction, and we still apply anti-oxidant compound at each termination for added protection. Every job we perform meets current NEC requirements along with Ackerman, MS's local code, and we pull permits whenever the work calls for one so your project stays fully inspectable.
Some Ackerman, MS homeowners with heavily deteriorated aluminum wiring decide a permanent fix makes more sense than ongoing correction work. For those situations, Wired Right Electrical offers full-home rewiring that swaps out aluminum branch circuits for modern copper throughout the property. It's a bigger project, but it puts the aluminum wiring question to rest for good. Our electricians will walk your home with you, explain what each option involves, and help you weigh correction against full rewiring based on your property and your budget.
Every aluminum wiring project in Ackerman, MS is carried out by, or directly supervised by, a certified master electrician who is personally accountable for the quality and code compliance of your job.
Before any work starts at your Ackerman, MS property, you'll have a written estimate covering labor, materials, and permit fees in full. What you approve is what you're billed, unless you sign off on added scope.
Wired Right Electrical takes care of every permit application, submission, and inspection appointment required by Ackerman, MS building authorities, keeping that process off your plate entirely.
Every job completed at your Ackerman, MS property is covered by our written workmanship warranty. Should a covered problem surface later, we'll come back and resolve it with no added labor charge.
Electrical problems at your Ackerman, MS property don't keep business hours, and neither do we. Our emergency line puts you in touch with a certified electrician dispatched to your address any time, day or night.
Wired Right Electrical has been doing licensed electrical work for Ackerman, MS homes and businesses since 2006. We're familiar with the local code requirements and the wiring issues typical of properties in this area.
Reach out to Wired Right Electrical today and talk through your aluminum wiring concerns with a certified electrician. We put every quote in writing, handle all required permits, and stand behind our work with a solid warranty.
☎ Call 1 (855) 471-2673